Posts Tagged ‘cgminer 3.7.2


We got a request for an up to date windows binary of the latest official sgminer 4.2.1 (source), so here it is. Do note that this is the standard version of sgminer that in intended for Scrypt mining and does not support a lot of alternative crypto algorithms, for that you will need to get sph-sgminer, a fork based on an older version of the official sgminer, namely sgminer 4.1.0. From the link below you can download the latest sgminer 4.2.1 Scrypt GPU miner for windows.

You can download sgminer 4.2.1 with Scrypt GPU support for Windows OS here…


We now have a merged mining pools for Blake-256 based crypto coins, currently supporting merged mining of Blakecoin and Photon, but for mining these you need a special version of cgminer with support for the algorithm being used by them. The Blake-256 algorithm hashrate is about 3x faster than what you are getting from the same hardware mining for Bitcoin. So for example with a Radeon R9 280X you can expect to get a hashrate of about 2-2.5 GH/s or more when mining Blackecoin (BLC) or other Blake-256-based crypto currencies such as Photon (PHO) for example. You cannot use the standard cgminer for mining Blake-256 crypto coins, you need to use a special version of cgminer with support for this algorithm (source) and you can download the windows version of cgminer 3.7.2 for Blake-256 mining below. Note that this version of cgminer is compiled with support for Blake-256 mining alone, you cannot mine other coins using different algorithms with it.

You can download cgminer 3.7.2 with Blake-256 Support for Windows OS here…


It seems that the community has figured out a way to do a voltage mod for the Gridseed 5-chip ASICs that allows for higher overclock frequencies and thus even higher hashrate. We have decided to try out the mod ourselves and report our own findings and results with our older and newer dual mining mode ASIC devices from Gridseed. What you need to do in terms of hardware modification to your miner is to solder a bridge on the place marked with the green line on the photo above. Then you need to run the latest version of the modified cgminer for Gridseed with an extra option for the gridseed options line “voltage=1”. Note that the space where you need to solder a bridge is very small, it is designed for SMD resistors and if you are not experienced with a soldering iron you will have trouble performing this modification by yourself. Also if you are not very careful you may damage the device by soldering something that should not be soldered and thus shorting the ASIC, so be very careful should you decide to mod the device or higher voltage!


After performing the hardware modification to our two miners that are from different revisions apparently we have tried running them with the modified cgminer (download link for the windows binary below, for the source). The older revision of the device we’ve got with CP2102 USB to UART Bridge Controller trying to run the setting to set the higher voltage from within cgminer returns an error about the firmware not supported. The device has a firmware version 01140116 and apparently this version is not supported, even modifying the cgminer to recognize it as supported firmware did not help in being able to overvolt and overclock the miner. The other newer ASIC device with STM32 Virtual COM port driver was with the correct firmware version 01140113 and the miner apparently did activate the overclock and overvolt mode. The power consumption of the device we have measure with the voltmod and running at 950 MHz frequency was with about 2W higher than at 850 without the voltmod, or with other words 8W instead of 6W (in fanless mode) with 2W more with the fan working (10W and 8W respectively). If you are doing the voltmod however we would not recommend to use the device in passive fanless cooling mode, though at 850 MHz and with no voltmod we have been running a single miner for already 48 hours without any issues.


With the increased voltage of the Gridchip GC3355 processors we were able to get from 850 MHz with no or very few HW errors (361 KHS) to 950 MHz with no to very little HW errors (404 KHS) after the modification. We could also go to about 425 KHS at 1000 MHz with very few HW errors, going up to 1050 MHz produces almost 450 KHS, however the number of HW errors we are getting at that frequency is significant, so the real performance is probably much lower than at lower clock speeds. What we would recommend as the most stable result is to go to 950 MHz as overclock frequency as good starting point after doing the voltmod and go up in 50 MHz steps to see how will your miners perform at higher frequencies and if they will do any better results. The latest version of cgminer supports overclock up to 1300 MHz in 50 MHz steps, so you can go pretty high, though you should be careful as the increased voltage and frequency might lead to damage of the device.

You can download cgminer 3.7.2 for Scrypt mining on Gridseed 5-chip GC3355 ASICs on Windows OS here…