Crypto Mining Blog
It Is All About BTC, LTC, ETH, DOGE, KAS mining as well as other alternative crypto currencies
Search
Posts Tagged ‘X11 ASIC miner’
Thermal Images of the iBeLink DM384M X11 ASIC Miner
16, Mar 2016
Time for a bit more in-depth look at the operating temperatures of the iBeLink DM384M X11 ASIC with the help of a thermal imaging camera. We are starting with the front and rear of the case that the mining ASIC uses, the front has four powerful Delta Electronics server fans that such cold air through the whole case where the mining blades are and the hot air exits directly through the back of the case. There are no other fans at the back, just open space for the hot air to exit the case of the device effectively cooling. The only other fan is the one of the server grade power supply that is mounted inside the case, another server grade Delta Electronics fan that is also powerful and noisy when in operation. The fans do not have power control, so they operate at maximum RPM all of the time making the device quite noisy, but also effectively cooled even in no so cool environment.
The four blades with ASIC chips are located on the side of the cooling fans and on the other side of the case is the power supply with the Raspberry Pi controller mounted over it. The side with the RPi and the power supply is pretty cold compared to the side where the four blade with 48 chips each are located. As one might expect the hottest part inside the miner are the ASIC chips, the rest remains pretty cold thanks to the high airflow provided by the cooling fans. Even the heatsink that are on the back of the PCB with the chips remain pretty cool thanks to the high airflow passing through them.
And now let us take a look at the chips themselves as the hottest element of the iBeLink DM384M X11 ASIC miners. Under the stock operating conditions they do remain with a surface temperature range of about 60-68 degrees Celsius as the temperature varies slightly depending on their position on the blade. As we’ve said already the cooling heatsink is not placed on top of the chips themselves, but instead is on the back of the PCB. This is the easier way to make things work, but not the most efficient for cooling as the chips use the PCB as a large heatspreader that then passes the heat to the large heatsink. This results in higher operating temperatures of the ASIC chips as there is no direct contact, but the temperatures are still Ok for normal operation. You should however be careful should you decide to overclock in order to get some extra hashrate as this will increase the operating temperatures of the chips. It seems that iBeLink has already chosen the optimal operating frequency for the device that results in very little HW errors while providing optimum performance. Further increasing the PLL frequency over the stock 110 MHz even with just a few Megahertz may result in increased percentage of HW errors.
- Published in: Mining Hardware|Tests and Reviews
- Related tags: ASIC DASH Miner, DASH ASIC, DASH ASIC miner, DM384M, DM384M miner, Dual Miner, Dualminer, iBeLink, iBeLink DM384M, iBeLink DM384M operating temperatures, iBeLink DM384M thermal images, iBeLink DM384M X11 ASIC Miner, Tiannengbo Group, TNB0301, TNB0301 ASIC, TNB0301 chip, X11 ASIC, X11 ASIC miner
Looking at the official specifications of the iBeLink DM384M X11 ASIC miner state that the device should be capable of 384 MHS X11 hashrate (plus/minus 10 percent) with a power consumption of 715W measured at the wall with 25 degrees Celsius ambient temperature. This should be the numbers for the default configuration, however we did some measurements ourselves in order to get more accurate results in order to be able to do better calculations about the cost of operating the device. We have already measured on NiceHash an average hashrate that is slightly above the official number of 384 MHS, so this is good, but what about the actual power usage and more importantly noise level. In our first impressions from the device we already mentioned that it is pretty noisy and not suitable for use in room where people will be present, but let us see what is the exact noise level as well.
The power supply built into the miner is an 850 Watts server grade one that is compatible with 100-240V range (for worldwide use). The exact model is ASPOWER U2A-A20850-D and according to the official specifications is it rated as 80 Plus Silver, so a high efficiency solution. At stock settings (110 MHz PLL) the power usage we have measured on the wall with 230V EU power input was 686 Watts as you can see on the photo, the power usage in Watts might be slightly higher in US and other 110-120V countries due to slightly lower power efficiency. Increasing the operating frequency with +1 MHz steps is resulting in the power usage going up with about 5-6W on each step, so the 850W capacity of the PSU should be able to take up some nice extra overclock if the chips are capable of working well when overclocked and cooled well. We are going to be doing more extensive testing about the overclocking potential with results on the power usage and performance changes, working temperatures and cooling very soon.
Now for the noise level, as already mentioned it is pretty high… just like from a rackmountable server for example. With a measurement showing about 72.6 dBA average it is perfect to be installed in a data center or a dedicated mining room, but it is not suitable for home miners as the noise level is too much for people to be in the same room for more than a few minutes… and even in the next room it might be quite noisy. The reason for the high level of noise is that the unit uses server grade fans by Delta Electronics and they are set to run at maximum RPM all the time (no temperature control). The same goes for the fan used in the power supply, a powerful Delta Electronics fan running at maximum RPM all the time, even though the PSU is highly efficient and there is not so much heat generated. The good thing about this default fans setup is that even at not that good conditions such as high ambient temperature the miner should be able to operate without any issues at optimum level. The not so good part is that small miners might have issues with the high level of noise and would probably want to do something to make it less noisy without compromising performance – this is possible with some modifications and we are already working on a solution to optimize the cooling, so more on that will be coming soon as well.
The iBeLink DM384M X11 ASIC miner is actually advertised as a DASH ASIC miner with DASH (previously known as DarkCoin) being the most popular and widely used X11 altcoin, is also currently rated as number 6 in terms of Market Capitalization. The ASIC miner can be used for any coin using a regular X11 algorithm for mining and in fact mining DASH with it is not the most profitable and anyone who purchases a new ASIC miner know that the first thing he needs to do is to ROI first in the fastest possible way and then can choose what to mine based on subjective preferences for example. So if you just got the 384 MHS X11 ASIC miner iBeLink DM384M you would probably want to head on to NiceHash and sell your hashrate to anyone willing to buy it as it will get you a few times more profit than directly mining for DASH at the moment according to the What to Mine service. The reason is simple, there are many new altcoins popping up all the time that use X11 algorithm and people are renting hashrate to mine them and with the increased demand for hashrate you might earn much more than mining for a more established coin such as DASH.
Here is how the average hashrate looks like when selling your X11 hashrate with the iBeLink DM384M X11 ASIC miner on NiceHash with the graph covering more than half a day. The average hashrate reported poolside is about 392 MHS with an average pay rate of about 0.5 BTC per Gigahash per Day. As mentioned earlier today you should update to cgminer 3.5.6 for the iBeLink machine in order to get the software that supports NiceHash’s extranonce in order to minimize stale shares and maximize profit. If the above trend continues for 24 hours this would mean an actual daily profit for the iBeLin X11 ASIC miner of about 0.2 BTC at the moment and that is pretty good when you are looking to get the fastest ROI time. Have in mind though that the profitability of X11 at NiceHash may vary more that if mining for any given more established X11 crypto currency with a stable exchange rate. There is always the possibility of jumping at the right time to the right new coin and making even better profit thanks to the high hashrate that the ASIC miner provides, but the risk is also higher and you may actually make less in the end this way.
– For more details on how to sell your hashrate using the NiceHash service…